Загрузить для cpe210 v2
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）How to find the hardware version on a TP-Link device?
- Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
CPE210(EU)_V2_20180928
|
|
Published Date: 2018-10-29
|
Language: English
|
File Size: 4.93 MB
|
|
Modifications and Bug Fixes:
1. Fixed the problem that the device may be reset to factory defaults due to unstable power.
2. Improved web UI display.
3. Fixed the problem that Transmit Power could be set as improper value.
4. Fixed the problem that when the wireless interference is serious, the client may be not connected to the AP when the WPA/WPA2 encryption mode is enabled.
5. Fixed the problem that the «Failed to get data» information may be wrongly displayed.
Notes:
1. For CPE210(EU) v2.0 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(EU)_V2_180117
|
|
Published Date: 2018-02-13
|
Language: English
|
File Size: 4.70 MB
|
|
Modifications and Bug Fixes:
1. Fixed the WPA2 vulnerability.
2. Fixed the Management VLAN issue that wireless clients will fail to obtian IP addresses when Management VLAN is enabled and given a same VLAN ID as that of SSID VLAN.
3. Improved web UI display.
4. Fixed the bug that a subnet range cannot be configured for the «Set Source» of the SNMP function.
5. Fixed the bug that CPE’s web management page can’t be accessed with a new username which contains special symbols.
6. Fixed the bug that when the management vlan and wireless encryption are enabled, wireless client may fail to connect to the CPE.
Note:
For CPE210 2.0
|
|
|
TP_Pharos_V2.1.6_170908
|
|
Published Date: 2017-09-08
|
Language: English
|
File Size: 4.91 MB
|
|
Modifications and Bug Fixes:
Bug Fixes:
1. Fixedx the bug that EU/US devices fail to switch operation mode in Quick Setup
2. Fixed the bug that PPPoE doesn’t work when configured as AP Router mode in Quick Setup.
Notes:
For CPE210 v2 only
|
|
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）How to find the hardware version on a TP-Link device?
- Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
CPE210(UN)_V3_20170828
|
|
Published Date: 2017-08-28
|
Language: English
|
File Size: 4.91 MB
|
|
Modifications:
Improve the interaction experience and stability.
Notes:
Firmware released for CPE210 V3.0 only
|
|
|
CPE210(UN)_V3_20170816
|
|
Published Date: 2017-08-16
|
Language: English
|
File Size: 4.91 MB
|
|
Modifications and Bug Fixes:
First firmware released for CPE210 v3.0
|
|
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）How to find the hardware version on a TP-Link device?
- Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
TP_PharOS_V2.1.0_170609
|
|
Published Date: 2017-06-09
|
Language: English
|
File Size: 4.97 MB
|
|
Modifications and Bug Fixes:
Modifications:
Optimize the UI design and improve the interaction experience.
|
|
|
TP_PharOS_1.3.3_160705
|
|
Published Date: 2016-07-05
|
Language: English
|
File Size: 5.08 MB
|
|
Modifications and Bug Fixes:
1. Fixed compatible issue with Mikrotik AP in Access Point mode.
2. Fixed WPA-PSK connection problem with none-standard SSID in test mode.
Notes:
For Pharos series, including CPE510,CPE210,WBS510, etc.
|
|
|
TP_PharOS_1.3.3_151215
|
|
Published Date: 2015-12-15
|
Language: Multi-language
|
File Size: 5.02 MB
|
|
Modifications and Bug Fixes:
Bug Fixted:
1. Fixed incompatibility issue that Pharos series can’t connect to MikroTik AP with WPA-PSK security mode when WDS is enabled.
2. Fixed the dialing problem when WAN port is of type L2TP/PPTP.
Notes:
For Pharos series, including CPE510,CPE210,WBS510, etc.
|
|
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）How to find the hardware version on a TP-Link device?
- Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
CPE210(EU)_V3.2_200612
|
|
Published Date: 2020-07-14
|
Language: English
|
File Size: 6.24 MB
|
|
Bug Fixed:
Fixed the bug that CPE may failed to connect with TP-Link Deco products.
Notes:
1. For CPE210(UN) v3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(EU)_V3.2_2.2.1 Build 200423
|
|
Published Date: 2020-06-11
|
Language: English
|
File Size: 6.24 MB
|
|
New Features/Enhancements:
1. Optimized the SSID scan process.
2. Extended the SSL certificate validity to 2029.
Bug Fixed:
1. Fixed the CVE-2020-8597 PPPoE security problem.
Notes:
1. For CPE210(UN/ES/EU) v3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(EU)_V3.0_20190620
|
|
Published Date: 2019-07-25
|
Language: English
|
File Size: 6.23 MB
|
|
Modifications&Enhancement
1. Upgrade OpenSSL version from 0.9.8k to 1.0.2q, and support TLSv1.2 protocol.
2. Optimize the memory usage of web server.
Notes:
1. For CPE210(EU) v3.0 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
Control Software
|
|
|
Yayın Tarihi: 2020-04-20
|
Dil: İngilizce
|
Dosya Boyutu: 71.91 MB
|
| İşletim Sistemi: Windows server2003/2008/2012/2016 and Vista/7/8/10 |
|
Modifications and Bug Fixes:
1. Added supporting CPE710;
2.Fixed display problems in the channel list.
3.Fixed MAX Tx Rate display problems when managing CPE605
Notes:
1. We suggest customers modify username and password after upgrading to the latest version of Pharos Control to improve security level.
2.Support managing CPE210/220/510/605/610/710
|
|
|
|
Yayın Tarihi: 2019-05-08
|
Dil: İngilizce
|
Dosya Boyutu: 15.77 MB
|
| İşletim Sistemi: Linux (Debian/Ubuntu) |
|
Modifications and Bug Fixes:
1. Fixed the problem that Pharos Control may not work normally in Turkish language operating system.
2. Improved security mechanism.
3. Improved log security level.
Notes:
1. When upgrading from the older version, it will cover previous data. So please backup the data first before updating the software.
2. Pharos Control only supports JRE1.7 and JRE1.8.
|
Programcılar İçin Açık Kaynak Kodu (GPL)
Aşağıdaki bilgiler programcılar içindir ve çoğu TP-Link ev kullanıcısı için gereksizdir.
TP-Link’in ürünleri kısmen GNU Genel Kamu Lisansı («GPL»), Version 1 / Version 2 / Version 3 veya GNU Lesser General Public License’a («LGPL») tabi yazılım kodu da dahil olmak üzere, üçüncü şahıslar tarafından geliştirilen yazılım kodunu içerir. İlgili yazılım koşulunu GPL lisans koşullarını izlemek için kullanabilirsiniz.
İlgili GPL lisans koşullarını buradan inceleyebilir, yazdırabilir ve indirebilirsiniz. TP-Link ürünlerinde kullanılan ilgili yazılımın GPL kaynak kodlarını, GPL Kod Merkezi altında GPL yazılım kodunu içeren TP-Link yazılımının bir listesi de dahil olmak üzere, doğrudan indirmek ve daha fazla bilgi almak için alırsınız.
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）How to find the hardware version on a TP-Link device?
- Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
CPE210(EU)_V3.2_2.2.1 Build 200423
|
|
Published Date: 2020-06-11
|
Language: English
|
File Size: 6.24 MB
|
|
New Features/Enhancements:
1. Optimized the SSID scan process.
2. Extended the SSL certificate validity to 2029.
Bug Fixed:
1. Fixed the CVE-2020-8597 PPPoE security problem.
Notes:
1. For CPE210(UN/ES/EU) v3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(EU)_V3.0_20190620
|
|
Published Date: 2019-07-25
|
Language: English
|
File Size: 6.23 MB
|
|
Modifications&Enhancement
1. Upgrade OpenSSL version from 0.9.8k to 1.0.2q, and support TLSv1.2 protocol.
2. Optimize the memory usage of web server.
Notes:
1. For CPE210(EU) v3.0 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(EU)_V3_20180928
|
|
Published Date: 2018-10-29
|
Language: English
|
File Size: 4.93 MB
|
|
Modifications and Bug Fixes:
1. Fixed the problem that the device may be reset to factory defaults due to unstable power.
2. Improved web UI display.
3. Fixed the problem that Transmit Power could be set as improper value.
4. Fixed the problem that when the wireless interference is serious, the client may be not connected to the AP when the WPA/WPA2 encryption mode is enabled.
5. Fixed the problem that the «Failed to get data» information may be wrongly displayed.
|
|
Control Software
|
|
|
Published Date: 2020-04-20
|
Language: English
|
File Size: 71.91 MB
|
| Operating System: Windows server2003/2008/2012/2016 and Vista/7/8/10 |
|
Modifications and Bug Fixes:
1. Added supporting CPE710;
2.Fixed display problems in the channel list.
3.Fixed MAX Tx Rate display problems when managing CPE605
Notes:
1. We suggest customers modify username and password after upgrading to the latest version of Pharos Control to improve security level.
2.Support managing CPE210/220/510/605/610/710
|
|
|
|
Published Date: 2019-05-08
|
Language: English
|
File Size: 15.77 MB
|
| Operating System: Linux (Debian/Ubuntu) |
|
Modifications and Bug Fixes:
1. Fixed the problem that Pharos Control may not work normally in Turkish language operating system.
2. Improved security mechanism.
3. Improved log security level.
Notes:
1. When upgrading from the older version, it will cover previous data. So please backup the data first before updating the software.
2. Pharos Control only supports JRE1.7 and JRE1.8.
|
|
|
|
Published Date: 2017-04-21
|
Language: English
|
File Size: 47.68 MB
|
| Operating System: Linux (Debian/Ubuntu) |
|
Modifications and Bug Fixes:
1. Use the B/S structure and inherit the functions of PharOS Control v1.
2. Add the Google Map and some other new functions.
Notes:
1. For PharOS CPE/WBS series wireless broadband products(including v1 devices).
2. Require to install Java (v1.7 or above) in Linux before running this software.
|
|
|
|
Published Date: 2016-07-12
|
Language: English
|
File Size: 87.31 MB
|
| Operating System: Win XP/2003/Vista/7/8 |
|
Modifications and Bug Fixes:
New Features/Enhancements:
1. Support creating task based on group.
2. Add SSL encryption option in Mail setting.
3. Enlarge subnet mask length in IPScan to 21 bits.
4. Support login method of GMail(OAuth2).
5. Add Manage operation when device’s status change from Managed to Unmanaged in Trigger tab.
Notes:
1. For Pharos series, including CPE510_V1,CPE210_V1,WBS510_V1,etc.
2. PharosControl_v1.1.4 can manage firmware PharOS 1.2.1 or later firmware versions.
|
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）How to find the hardware version on a TP-Link device?
- Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
CPE210(US)_V2_200612
|
|
Published Date: 2020-07-14
|
Language: English
|
File Size: 6.24 MB
|
|
New Features/Enhancements:
1. Optimized the SSID scan process.
2. Extended the SSL certificate validity to 2029.
Bug Fixed:
1. Fixed the CVE-2020-8597 PPPoE security problem.
2. Fixed the bug that CPE may failed to connect with TP-Link Deco products.
Notes:
1. For CPE210(US) v2.0/v2.8 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(US)_V2_20190620
|
|
Published Date: 2019-07-25
|
Language: English
|
File Size: 6.23 MB
|
|
Modifications&Enhancement
1. Upgrade OpenSSL version from 0.9.8k to 1.0.2q, and support TLSv1.2 protocol.
2. Optimize the memory usage of web server.
Notes:
1. For CPE210(US) v2.0 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(US)_V2_20190228
|
|
Published Date: 2019-04-11
|
Language: English
|
File Size: 6.03 MB
|
|
Modifications and Bug Fixes:
1.Improved web UI display.
2.Added Antenna Alignment function.
3.Now the https is enabled by default.
4.Added IPV6 function.
|
|
Programcılar İçin Açık Kaynak Kodu (GPL)
Aşağıdaki bilgiler programcılar içindir ve çoğu TP-Link ev kullanıcısı için gereksizdir.
TP-Link’in ürünleri kısmen GNU Genel Kamu Lisansı («GPL»), Version 1 / Version 2 / Version 3 veya GNU Lesser General Public License’a («LGPL») tabi yazılım kodu da dahil olmak üzere, üçüncü şahıslar tarafından geliştirilen yazılım kodunu içerir. İlgili yazılım koşulunu GPL lisans koşullarını izlemek için kullanabilirsiniz.
İlgili GPL lisans koşullarını buradan inceleyebilir, yazdırabilir ve indirebilirsiniz. TP-Link ürünlerinde kullanılan ilgili yazılımın GPL kaynak kodlarını, GPL Kod Merkezi altında GPL yazılım kodunu içeren TP-Link yazılımının bir listesi de dahil olmak üzere, doğrudan indirmek ve daha fazla bilgi almak için alırsınız.
Open Source Code For Programmers (GPL)
Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License («LGPL»). You may use the respective software condition to following the GPL licence terms.
You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-Link products for direct download and further information, including a list of TP-Link software that contain GPL software code under GPL Code Center.
Open Source Code For Programmers (GPL)
Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License («LGPL»). You may use the respective software condition to following the GPL licence terms.
You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-Link products for direct download and further information, including a list of TP-Link software that contain GPL software code under GPL Code Center.
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）จะค้นหาเวอร์ชั่นฮาร์ดแวร์บนอุปกรณ์ TP-Link ได้อย่างไร
- Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
CPE210(UN)_V3.2_200612
|
|
Published Date: 2020-07-14
|
Language: อังกฤษ
|
File Size: 6.24 MB
|
|
Bug Fixed:
Fixed the bug that CPE may failed to connect with TP-Link Deco products.
Notes:
1. For CPE210(UN) v3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(UN)_V3.0_20190620
|
|
Published Date: 2019-07-25
|
Language: อังกฤษ
|
File Size: 6.23 MB
|
|
Modifications&Enhancement
1. Upgrade OpenSSL version from 0.9.8k to 1.0.2q, and support TLSv1.2 protocol.
2. Optimize the memory usage of web server.
Notes:
1. For CPE210(UN) v3.0 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(UN)_V3_20190125
|
|
Published Date: 2019-02-28
|
Language: อังกฤษ
|
File Size: 6.02 MB
|
|
Modifications and Bug Fixes:
1.Improved web UI display.
2.Added Antenna Alignment function.
3.Now the https is enabled by default.
4.Added IPV6 function.
Notes:
1. For CPE210(UN) v3.0 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
Güncelleme İçin
ÖNEMLİ: Güncelleme hatalarını önlemek için, güncelleme işlemine devam etmeden önce aşağıdakileri okuyunuz
- Cihaz yazılımı sürümü için, cihazınızın donanım sürümünü doğrulayın. Yazılımın yanlış güncellenmesi cihazınıza zarar verebilir ve garantiyi geçersiz kılabilir. (Normalde V1.x = V1)
Bölgeniz için olmayan bir firmware güncellemesi önerilmemektedir. Bölgenizi seçmek ve en uygun firmware sürümünü indirmek için lütfen burayı tıklayın. (Örneğin, AB’nin ve ABD’nin üretici yazılımı farklı donanım sürümleridir)
- Ürünü kalıcı bir hasara uğratmamak için güncelleme işlemi sırasında gücü KAPATMAYIN.
- Yazılımı kablosuz bağlantı yoluyla GÜNCELLEMEYİN.
- Kullanıcıların bilgisayardaki tüm Internet uygulamalarını durdurmaları veya güncellemeden önce Internet hattını cihazdan çıkarmanız önerilir.
- Güncellemeden önce indirdiğiniz dosyayı ayıklamak için WinZIP veya WinRAR gibi yazılımlar kullanın.
|
CPE210(EU)_V3.2_200612
|
|
Yayın Tarihi: 2020-07-14
|
Dil: İngilizce
|
Dosya Boyutu: 6.24 MB
|
|
Bug Fixed:
Fixed the bug that CPE may failed to connect with TP-Link Deco products.
Notes:
1. For CPE210(UN) v3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(UN)_V3.2_200612
|
|
Yayın Tarihi: 2020-07-14
|
Dil: İngilizce
|
Dosya Boyutu: 6.24 MB
|
|
Bug Fixed:
Fixed the bug that CPE may failed to connect with TP-Link Deco products.
Notes:
1. For CPE210(UN) v3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(EU)_V3.2_2.2.1 Build 200423
|
|
Yayın Tarihi: 2020-06-11
|
Dil: İngilizce
|
Dosya Boyutu: 6.24 MB
|
|
New Features/Enhancements:
1. Optimized the SSID scan process.
2. Extended the SSL certificate validity to 2029.
Bug Fixed:
1. Fixed the CVE-2020-8597 PPPoE security problem.
Notes:
1. For CPE210(UN/ES/EU) v3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
Control Software
|
|
|
Published Date: 2020-04-20
|
Language: English
|
File Size: 71.91 MB
|
| Operating System: Windows server2003/2008/2012/2016 and Vista/7/8/10 |
|
Modifications and Bug Fixes:
1. Added supporting CPE710;
2.Fixed display problems in the channel list.
3.Fixed MAX Tx Rate display problems when managing CPE605
Notes:
1. We suggest customers modify username and password after upgrading to the latest version of Pharos Control to improve security level.
2.Support managing CPE210/220/510/605/610/710
|
|
|
|
Published Date: 2019-05-08
|
Language: English
|
File Size: 15.77 MB
|
| Operating System: Linux (Debian/Ubuntu) |
|
Modifications and Bug Fixes:
1. Fixed the problem that Pharos Control may not work normally in Turkish language operating system.
2. Improved security mechanism.
3. Improved log security level.
Notes:
1. When upgrading from the older version, it will cover previous data. So please backup the data first before updating the software.
2. Pharos Control only supports JRE1.7 and JRE1.8.
|
|
|
|
Published Date: 2017-04-21
|
Language: English
|
File Size: 47.68MB
|
| Operating System: Linux (Debian/Ubuntu) |
|
Modifications and Bug Fixes:
1. Use the B/S structure and inherit the functions of PharOS Control v1.
2. Add the Google Map and some other new functions.
Notes:
1. For PharOS CPE/WBS series wireless broadband products(including v1 devices).
2. Require to install Java (v1.7 or above) in Linux before running this software.
|
ДЛЯ ОБНОВЛЕНИЯ
ВАЖНО: Чтобы избежать проблем при обновлении ПО, пожалуйста, прочитайте следующую информацию по процедуре обновления. Проверьте соответствие аппаратной версии и версии ПО
Установка неправильной версии ПО может повредить ваше устройство и аннулировать гарантию. (Обычно V1.x =V1)
Проверьте соответствие аппаратной версии и версии ПО. Установка неправильной версии ПО может повредить ваше устройство и аннулировать гарантию. (Обычно V1.x =V1)
НЕ рекомендуется устанавливать версию ПО, не предназначенную для вашего региона. Нажмите здесь для выбора региона и загрузите наиболее актуальную версию ПО.
- НЕ отключайте питание во время процесса обновления, поскольку это может нанести урон маршрутизатору
- НЕ обновляйте ПО маршрутизатора по Wi-Fi, за исключением тех случаев, когда это является единственно возможным способом.
- Рекомендуется, чтобы все пользователи прекратили использовать все интернет-приложения на компьютере или отключили сетевой кабель от клиентских устройств перед обновлением.
Примечание: Конфигурационные файлы могут быть некорректно установлены на новые версии встроенного ПО, требующие сброса на заводские настройки.
Рекомендации по обновлению ПО: Wi-Fi роутер, Wi-Fi роутер с модемом ADSL2+, Усилитель Wi-Fi сигнала
|
CPE210(UN)_V2_20180928
|
|
Дата публикации: 2018-10-29
|
Язык: Английский
|
Размер файла: 4.93 MB
|
|
Modifications and Bug Fixes:
1. Fixed the problem that the device may be reset to factory defaults due to unstable power.
2. Improved web UI display.
3. Fixed the problem that Transmit Power could be set as improper value.
4. Fixed the problem that when the wireless interference is serious, the client may be not connected to the AP when the WPA/WPA2 encryption mode is enabled.
5. Fixed the problem that the «Failed to get data» information may be wrongly displayed.
Notes:
1. For CPE210(UN) v2.0 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(EU)_V2_20180928
|
|
Дата публикации: 2018-10-29
|
Язык: Английский
|
Размер файла: 4.93 MB
|
|
Modifications and Bug Fixes:
1. Fixed the problem that the device may be reset to factory defaults due to unstable power.
2. Improved web UI display.
3. Fixed the problem that Transmit Power could be set as improper value.
4. Fixed the problem that when the wireless interference is serious, the client may be not connected to the AP when the WPA/WPA2 encryption mode is enabled.
5. Fixed the problem that the «Failed to get data» information may be wrongly displayed.
Notes:
1. For CPE210(EU) v2.0 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(UN)_V2_180117
|
|
Дата публикации: 2018-02-13
|
Язык: Английский
|
Размер файла: 4.70 MB
|
|
Modifications and Bug Fixes:
1. Fixed the WPA2 vulnerability.
2. Fixed the Management VLAN issue that wireless clients will fail to obtian IP addresses when Management VLAN is enabled and given a same VLAN ID as that of SSID VLAN.
3. Improved web UI display.
4. Fixed the bug that a subnet range cannot be configured for the «Set Source» of the SNMP function.
5. Fixed the bug that CPE’s web management page can’t be accessed with a new username which contains special symbols.
6. Fixed the bug that when the management vlan and wireless encryption are enabled, wireless client may fail to connect to the CPE.
Note:
For CPE210 2.0
|
|
Open Source Code For Programmers (GPL)
Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License («LGPL»). You may use the respective software condition to following the GPL licence terms.
You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-Link products for direct download and further information, including a list of TP-Link software that contain GPL software code under GPL Code Center.
Open Source Code For Programmers (GPL)
Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License («LGPL»). You may use the respective software condition to following the GPL licence terms.
You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-Link products for direct download and further information, including a list of TP-Link software that contain GPL software code under GPL Code Center.
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）Làm sao để biết phiên bản phần cứng của thiết bị TP-Link
- Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it’s recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It’s recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
CPE210(EU)_V3.2_2.2.1 Build 200423
|
|
Ngày Phát Hành: 2020-06-11
|
Ngôn Ngữ: English
|
File Size: 6.24 MB
|
|
New Features/Enhancements:
1. Optimized the SSID scan process.
2. Extended the SSL certificate validity to 2029.
Bug Fixed:
1. Fixed the CVE-2020-8597 PPPoE security problem.
Notes:
1. For CPE210(UN/ES/EU) v3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(UN)_V3.2_2.2.1 Build 200423
|
|
Ngày Phát Hành: 2020-06-11
|
Ngôn Ngữ: English
|
File Size: 6.24 MB
|
|
New Features/Enhancements:
1. Optimized the SSID scan process.
2. Extended the SSL certificate validity to 2029.
Bug Fixed:
1. Fixed the CVE-2020-8597 PPPoE security problem.
Notes:
1. For CPE210(UN/ES/EU) v3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
|
CPE210(UN)_V3.2_2.2.0 Build 190815
|
|
Ngày Phát Hành: 2019-10-09
|
Ngôn Ngữ: English
|
File Size: 6.23 MB
|
|
First firmware released for CPE210(UN) 3.2.
Notes:
1. For CPE210(UN) 3.2 only.
2. Your device’s configuration won’t be lost after upgrading.
|
|
Open Source Code For Programmers (GPL)
Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License («LGPL»). You may use the respective software condition to following the GPL licence terms.
You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-Link products for direct download and further information, including a list of TP-Link software that contain GPL software code under GPL Code Center.
